Woodworking & Workshop/ Carpentry/ Outdoor Projects/ Decks, Patios & Porches/ Outdoor Structures/ Pergolas/

Building A Pergola – Learn How to Build an Attached Pergola for Your Patio


How to build a pergola that’s attached to your house. Clear, step-by-step video instructions for building an attached pergola that also shades a patio.

Build a pergola or arbor to serve as a semi-open patio roof. Made of two-by-eight beams, the roof rests on four-by-four posts on one side and attaches to your home on the other. This design uses three layers of interlocking roof beams, but remains open to sky and breeze to offer the best combined features of patio, porch and deck.

Read More
using a bar level
Step 1

Mark the Pergola Elevation and Width on the House

Mark two perpendicular lines from your home's soffits to the patio to mark the desired elevation of the pergola, spacing them at the same width as the patio's concrete pad. Use a bar level to ensure the lines are vertical.

notched beams
Step 2

Cut and Notch Three Beams for the First Roof Layer

Cut three two-by-eight beams for the first roof layer that parallels the house. Notch them with a jigsaw to support four of six second layer beams--the other two will butt against the ends of the first layer's beams.

tightening lag screw
Step 3

Level, Pre-drill and Attach the Pergola Ledger to the House

Level the ledger and pre-drill holes for lag screws through the ledger, and fascia board into the side of the house. Tighten the lag screws with a ratchet.

inserting an expansion anchor into concrete
Step 4

Drill Patio for Post Brackets and Attach with Expansion Anchors

Position the post brackets, marking their centers on the concrete with a hammer and sharp instrument. Drill a hole at each mark, insert an expansion anchor through the bracket into the concrete, and tighten it with a ratchet.

installing post supports
Step 5

Install Post Supports and Posts to Brackets with Heavy-gauge Nails

Install post supports in the brackets to raise the posts above concrete and moisture to prevent rotting. Hold the posts in vertical position and secure each to its bracket with a hammer and heavy-gauge galvanized nails.

using bar level
Step 6

Hold Posts Vertical with Temporary Stakes and Braces

Screw pairs of temporary braces to stakes in the ground and clamp the braces to the posts to keep them vertical in both directions for the remainder of the project. Use a bar level to confirm the posts are plumb.

driving screw into beam
Step 7

Screw First-layer End Beams to the Posts

Align and clamp notched end beams in the first layer to the posts at the correct elevation. Pre-drill holes with a countersunk bit. Drive the stainless-steel screws into the beams and posts using a square-ended bit.

tracing decorative curve onto beam
Step 8

Cut and Curve One End of Six Second-layer Beams

Cut six second-layer beams with a decorative curve on one end. They'll be longer that the depth of the patio and run perpendicular to the house. Notch the bottom edges to interlock with the notches on the first layer's beams.

interlocking notched beams
Step 9

Interlock Layer-Two beams to Layer-One Beams and Trim the Posts

Notch the second-layer beams eight times for the eight beams in the final layer and then interlock them to the first layer. Trim the post tops flush with the top of the beams with a Japanese handsaw.

installing third-layer beams
Step 10

Cut Eight Third-layer Beams, Notching to Interlock with Beams Below

Cut eight beams with both ends curved for the third/final layer. Cut six shallower notches in the bottom edges to interlock with notches on the second layer. Fit them together and tap with a mallet to seat them.

Ron Hazelton Headshot

Have your project done by a local, qualified professional.


Not everyone is in a position to do a project themselves. That's why I've partnered with HomeAdvisor Powered by Angi to provide you with free quotes from qualified local professionals.


Related Tips

Blog Articles

December 14, 2021

How to Make Moveable Drawer Dividers

This technique will allow you to create drawer dividers that are moveable and adjustable for any drawer in your home.

December 03, 2021

How to Enlarge a Hole with a Hole Saw

If you've already cut a large diameter hole with a hole saw and now need to enlarge it, you'll need to know this trick in order to get it done right.

November 18, 2021

How to Make a DIY House Number Sign

In this post, I’ll show you step-by-step how I made my DIY house number sign - everything from considerations and decisions to make upfront through the whole process until completion.

Recent Articles